Brakes

** Click on the images to see them at a larger size**

What do the inside of Airheart brakes look like?  

We all assume that brakes that have been unused for nearly 40 years need to be upgraded.   Should be easy.  Pull out the the piston and change what ever is included in a "brake kit."   Dad said we needed brake kits. Guys on the forums said we needed brake kits.  I don't know what's in a brake kit, but I ordered two from Greg @ Rapid Racing.  

Here is the piston half of the brake, prior to cleaning.  Piston in the middle.  Gummy, but pretty simple.

Here it is after cleaning.  We tried to remove the piston by blowing compressed air into the system, like Dad had done while he was active in karting.  Nope, the piston was stuck solid. We gently "persuaded" the piston back into the cylinder, but the compressed air would not move it back out.  

Finally, we decided to put the brake system back together and let hydraulics do the work. 

Here is the master cylinder being cleaned.

Reassembling the brake system on the kart.  Always good to check where the rods go... in relation to the tie rods. :-)   Also notice the clothing... it was 80 degrees!  Check out the last post when it was 30 degrees, and I had my long johns on.

A short section of tubing was used to connect the brake housing to the master cylinder.  Finally, after bleeding the air out, the piston moved out.  BUT not all the way.  

 The back seal was broken so we were sucking air.  I happened to put my thumb over it while Dad pumped the pedal.  BINGO!  Fluid, dirt and the piston went flying!   The second brake was in the same condition, but with this knowledge was apart in just a few minutes.

That allowed us to clean everything with gasoline and get the hard stuff off with emery cloth (which Dad has had since using it to hone the cylinder of this same engine...in the early 1970s!!  Seems he knew he would use it again.)

So that is what the inside of Airheart brakes look like!  This was Dad's first time to tear down the brakes. They had always just worked.  Piston, O-rings.  So what is in the brake kit?  Just a couple 0-rings for that price?  Well, we looked a little deeper and found all kinds of good stuff.   So, yes, the kits are necessary! 

Nuthin' like a wheel brush to clean the hard stuff off of brake rotors!

Next up was the tanks.  I cleaned the dust with gasoline and gently pulled off the 200mph tape and #24.  Nice of Jeffie to used Dad's last race number.  Dad will display it in the tool locker.

Reminder, there are rubber grommets in the holes that attach the tanks.  Without proper lubrication (or forethought), they can be hard to move.

 One.

 Two.  I found out that fuel is only put into the tank near the engine.  No need for fuel in two tanks.  the dummy tank is just a bumper.

 

Finally, we ended the day with the throttle mechanism.  Only took us 2-3 tries, but we got it.  The throttle link to the spring goes under the tie rod.   AND don't put the tiny cable clamp allen bolts, which are the size of a grain of rice, down on the tank!  They will roll away and are hard to see.  Thanks goodness for thick, rough welds!

That leaves just a few things to do... the really fun part!

Rear End

Today's task was to re-assemble the rear end.  It only took us 2 attempts to make sure all was correct.  Had a little problem remembering the axle bearing housings go on the same side.  Take it all apart!  That's OK... I won't forget next time.

Bottom of the steering column.  All snug and secure.

 Both housings on the inside.  I am sure glad Dad caught the "play" in the axle.  Funny how I don't have photos of the WRONG way.

All secure and ready.  The hangers and grommets are on for the bottom frame.

Hangers. Some pieces I did not paint.  Keeps a reminder of what it originally was like.

Brakes and tanks next time. Maybe the pedal mechanisms.

Re-Assembly Started

January 24, 2012 --  On a frigid, 15 degree Friday, Dad and I cleaned engine parts in the garage, instead of the barn,  with the best all-around cleanser: Gasoline.  Sorry, no pictures.

--------------

Finally... Parts are going back together!

As Dad says, "this is the easy stuff"

Removing the material that protected the allen holes

 Just a bunch of metal tubing and rough welds

Clean! and ready for a bushing

 Dad hammering out some dings

First piece back on.. the rear floor pan

 Rivets.  Randy, thanks for the tool

 Riveting the front floor panel. This is the bottom.  That is Chrome spraypaint.. not bad for Rattlecan

 Top, painted flat black

 This is the fiberglass seat form.  Took awhile to figure how we did this.  Rivets are too short.

 Then we remembered the mangled little bolts in the storage box. So we scrounged for some bolts. 

 That fits!  Just bend it over to secure it  (oh, then we found the unmangled little bolts that were removed from that spot. Oh well!)

 Gleaming!

 The seat form is not long enough to rivet on the back tube. Notice the cuts on the side, so we may need to strap it after seat testing.

****I was checking out tear-down photos and found out there is a metal sheet that goes here... ****

 Riveting Snaps

  Upholstery!

 Headrest

 Steering!   Had to remember and figure out the order of washers and bearings

 Ready to be tightened

Almost a kart again!  Now the hard part starts....

Painting the Frame

Over Christmas I was able to find Lodge's Sandblasting, who prepped the frame for painting. The old blue paint and original red paint was stripped away.

Hauling it from sandblasting to be painted. Great day to transfer bare ferrous-metals! Just don't drop in the snow!

I was able to use the spray booth at my workplace. Wonderful! I would have loved to hang it to paint, but this worked just fine. Here it is ready to go.

Raw metal. No primer yet.

Notice foam filler protecting the allen holes in the collars.

The sandblaster hit the cracks with a little weld, but I may need to hit it again my self.

There is some primer on the cross member.

AHHH... Color! It is a bit darker than I anticipated. But it is a standard color for enamel in a spray can. Rattlecan is a new term I have found.

Protecting the bushing slots

She's Blue!

I have some metalic aluminum spray enamel that I may use on some details.

Next up is cleaning up all the other parts, rebuilding the frame, and rebuilding the engine.

Fun in the "off" season

Here are some images of my first "mod" for rFactor, the Red Devil kart. rFactor is designed for users to create vehicles and tracks. The kart was created with Blender, a free 3D modeling program. I recreated the Indianapolis Raceway Park road course with Bob's Track Builder.

These images are from an early version. The bad shadows and head movements have been fixed.

pits at IRP, looking east towards the 5/8 mile oval.  Old main tower at far right.

pits at IRP

IRP backstretch. notice old tower at right

on the grid at IRP

scramble at start

driver's eye view, too far left coming out of 1 at IRP

Here is a link to a video:
http://www.youtube.com/watch?v=VAO39V0cOkA
 (bonus points for guessing who the driver/kart is based on)

If interested:
http://rfactor.net/